HY16F198B-L064 is a liquid crystal drive circuit (Liquid Crystal Display, LCD), low power consumption, high performance mixed signal processing microcontroller (Mixed Signal Micro Controller, MCU), suitable for precise measurement and control, the chip can It works in a wide voltage range from 2.2V to 3.6V, and can run up to 16MHz. It has built-in 64/32/16KByte embedded flash memory (Flash ROM) and 8/4/2KByte static random access memory (SRAM). HY16F19xB series products integrate high-precision 24-bit modulating analog converter (ΣΔADC), rail-to-rail operational amplifier (OPAMP), 8-bit resistance ladder, hardware real-time clock (Hardware RTC), multi-function comparison (Multi-Comparator ), providing high-performance peripheral interfaces, such as UARTX2, SPI, I2C, GPIO, and built-in power management system functions. Support low voltage detection, multiple peripheral interface wake-up functions. HY16F198B-L064 is a 32-bit microcontroller with low voltage, low power consumption, low standby current, high integration and high efficiency operation, and supports C/C++ development platform. Abundant resources allow designers to complete a low-power, low-cost mixed-signal processing system.

The analog front-end circuit in this controller includes an 8-bit resistance ladder, a rail-to-rail operational amplifier (OPA), and a rail-to-rail input comparator (CMP). Among them, the 8-bit digital-to-analog converter guarantees monotonicity. It is a ladder-shaped digital resistor, and each least significant bit (LSB) is close to 730 ohms. The resistor has a low temperature coefficient. Rail-to-rail op amps have an input network and can be used in differential analog circuit configurations such as integrators, current-to-voltage converters, programmable-gain amplifiers, and step-by-step analog-to-digital converters. The rail-to-rail input comparator monitors the continuity of the analog signal with very low power consumption. It can be used as a supply voltage monitor, an external wake-up trigger source, or a capacitive touch key driver.

An ultra-low noise 24-bit analog-to-digital converter (ADC) is embedded. The maximum output rate is 10.24KSPS with 21-bit effective number of bits (ENOB, Effective Number OF Bit), and the minimum analytic input signal is 65nV RMS Noise (Root-Mean-Square). This low-noise amplifier with programmable gain (PGA) is used with an analog-to-digital converter with a maximum gain of 128x magnification. Built-in a 4-bit digital-to-analog converter to the input of the analog-to-digital converter to expand the measurement range.

Power management provides an optional analog circuit to regulate the voltage, which can be used as a voltage reference source and sensor power drive. The CPU core working power is also provided by the internal linear regulated power supply. The charge pump is used to block power interference from the system. 64KByte embedded flash memory can be used to execute programs and store data. Data can also be stored in flash memory during program execution. At the same time built-in 8KByte static random access memory for system use.

Using a 32-bit high-performance mixed-signal processing microcontroller core, it can execute one instruction per clock cycle, up to 16MIPS (Millions of Instructions Per Second), with low power consumption indicators. Hongkang Technology provides some easy-to-use program writing tools, and users can write programs in C/C++ language or assembly language under the development platform. The chip has a circuit simulation function, providing an environment for easy debugging. The chip can work at a working voltage of 2.2V to 3.6V and a temperature environment of -40°C to 85°C.

Product Features:

digital quantity

• 32-bit 1T Andes Core N801 core

• Support C development environment instruction set

• Wide operating voltage 2.2V to 3.6V

• Working temperature -40to85℃

• Low power consumption:

- Operating mode: 0.6mA@CPU_CK: 2MHz/2

- Standby mode: 5uA@LSRC=35KHz

- Sleep mode: Typ.2.5uA

• 64KB Flash ROM

• 8KB SRAM

• 16-bit Timer A, Timer B(X2), Timer C

• 16-bit PWM controller and signal capture function

• Hardware implementation of I2C/32-bit SPI/UART(X2) communication interface

• Hardware implementation clock RTC

• 32 programmable multiplexed I/Os

- 16 general-purpose digital I/O ports

- 16 selectable LCD ports or digital I/O ports

• 4x36~6x34 LCD liquid crystal driver

- 1/3, 1/4, 1/5, 1/6 Duty and 1/3 Bias selection

- Support R Type driver

- Built-in Charge Pump regulator circuit, providing 4-segment VLCD bias voltage, 3.3V, 3.0V, 2.8V, or2.6V

Analog

• Built-in low noise 24-bitΣADC

- Input referred noise as low as 65nVrms

- Conversion rate up to 10KSPS

- Input magnification up to 128

- Operating voltage is 2.4V to 3.6V

• External high-speed crystal oscillator frequency up to 16MHz

• External low-speed crystal shock as low as 32768Hz

• Built-in RC high speed oscillator frequency up to 16MHz

• Built-in RC low-speed oscillator frequency as low as 35KHz

• Power module

- Charge pump boost regulated power supply (CP_O)

- Built-in four-stage adjustable regulated power supply (VDDA)

- 1.2V Bandgap Reference Voltage (REFO)

• 8-BIT programmable digital resistor

- Programmable resistor divider

- Resistor guarantees monotonicity

• Rail-to-Rail Operational Amplifier OPAMP

- CMOS input, 1MHz gain bandwidth

- can be used as a comparator

• Multifunction Comparator

- Support touch button measurement

- Low voltage detection circuit

 

Internal block diagram

The AP8000 universal programmer independently developed by Acroview Technology includes three parts: the host, the base plate, and the adapter seat.

The host supports USB and NET connections, allowing Automatic programming to be networked to achieve the purpose of simultaneously controlling multiple automatic ic programmers for simultaneous programming. The built-in chip safety protection circuit ensures that even if the chip is reversed or a short circuit caused by other reasons can be detected immediately and the power will be cut off to ensure the safety of the chip and programmer. Embedded high-speed FPGA greatly accelerates data transmission and processing. There is an SD card slot on the back of the main unit. Put the project file produced by the PC software into the root directory of the SD card and insert it into the card slot. The project file can be selected, loaded, and programmed through the buttons on the programmer. command, in order to achieve the purpose of operating without PC, which greatly reduces the cost of PC hardware configuration, and can be conveniently and quickly matched with the working environment.

AP8000 makes the mainframe more expandable by adding an adapter board to the backplane. Currently, it supports devices produced by all mainstream semiconductor manufacturers, including TI, ST, MicroChip, Atmel, Hynix, Macronix, Micron, Samsung, Toshiba, etc. Supported device types include NAND, NOR, MCU, CPLD, FPGA, EMMC, etc., and support file formats including Intel Hex, Motorola S, Binary, POF, etc.

About HYCON Technology: HYCON Technology (HYCON) was established in 2007. It is a leading manufacturer of chip design with analog circuits as its core technology. It specializes in the development of high-performance data converters and provides chip integration solutions based on hybrid Signal microcontroller chips, battery management chips and touch technology chips are the main products.

About Acroview Technology: ACROVIEW is Global Leader of Semiconductor chip programming solutions. The company insists on changing the world with technology, driving the future with intelligence, and continuously creating value for customers. Acroview's AP8000 universal ic programmer platform and the latest IPS5000 programming automation solution provide one-stop solutions for customers in the semiconductor and electronics manufacturing fields. The company has served global leading customers including Huawei, BYD, Foxconn and so on.